|
|
Regular
Posts: 82
| Looking to order a branding iron to freeze brand a few colts... We have not had the best luck with our current iron and I am thinking we don't have the right metal for that bright white brand I'm looking for...
Where have y'all had the best luck ordering freeze brands from? Any certain makers to stay away from? Our brand is super simple, so I don't need anything fancy - just quality. TIA! |
|
| |
|
 
Location: Not Where I Want to Be | http://www.pittsburgfoundry.com/#freeze-brands
Edited by 1DSoon 2016-10-31 12:51 PM
|
|
| |
|
 Good Grief!
Posts: 6343
 
Location: Cap'n Joan Rotgut.....alberta | My freeze brand is made of brass..and to get the nice bright white the timing has to be just so......m |
|
| |
|
 Take a Picture
Posts: 12838
| Mine is brass and got it from L and H branding irons
|
|
| |
|
 Expert
Posts: 2097
Location: Deep South | Mine is also brass, and like already mentioned, you're timing has to be impeccable for a perfect white brand.
We shave the hair as close as possible. Wipe with rubbing alcohol to get it clean. Then press the brand hard against them, gently rocking it up and down for 10 seconds. This is for older horses. I've heard if branding horses younger than a year older their skin is thinner and you can only leave it on for about 7 seconds. |
|
| |
|
 Midget Lover
Location: Kentucky |
This is where mine came from.
|
|
| |
|
 Horsey Gene Carrier
Posts: 1888
Location: LaBelle, Florida | I have 2...a larger iron one and have used it for freezing and hot branding.
My smaller one is brass for freezing.
Timing is everything on a freeze brand reguardless of what is used for the iron.
|
|
| |
|
Regular
Posts: 82
| What size are your freeze brands? I assumed their was just a standard but am seeing several size options with L & H. |
|
| |
|
Good Grief!
Posts: 6343
Location: Cap'n Joan Rotgut.....alberta | Mines 2"......m |
|
| |
|
 Expert
Posts: 5290
| BamaCanChaser - 2016-10-31 11:18 AM
Mine is also brass, and like already mentioned, you're timing has to be impeccable for a perfect white brand.
We shave the hair as close as possible. Wipe with rubbing alcohol to get it clean. Then press the brand hard against them, gently rocking it up and down for 10 seconds. This is for older horses. I've heard if branding horses younger than a year older their skin is thinner and you can only leave it on for about 7 seconds.
I freeze brand as a side job of sorts... I use liquid nitrogen ( Best predictable method) and Minimum 17 seconds to 24 seconds depending on color of the horse. I can't imagine 7-10 seconds getting the job done. :) |
|
| |
|
 Expert
Posts: 4625
Location: Desert Land | This is where I got my brand from and am very pleased with it:
http://flying45.com/ |
|
| |
|
The Advice Guru
Posts: 6419
| FLITASTIC - 2016-10-31 3:02 PM
BamaCanChaser - 2016-10-31 11:18 AM
Mine is also brass, and like already mentioned, you're timing has to be impeccable for a perfect white brand.
We shave the hair as close as possible. Wipe with rubbing alcohol to get it clean. Then press the brand hard against them, gently rocking it up and down for 10 seconds. This is for older horses. I've heard if branding horses younger than a year older their skin is thinner and you can only leave it on for about 7 seconds.
I freeze brand as a side job of sorts... I use liquid nitrogen ( Best predictable method ) and Minimum 17 seconds to 24 seconds depending on color of the horse. I can't imagine 7-10 seconds getting the job done. : )
Interesting I get the vets to do it and they leave it on for 45 seconds |
|
| |
|
The Advice Guru
Posts: 6419
| I was told stainless steel does the same as brads. I got one done for foals but haven't used it yet. |
|
| |
|
 Off the Wall Wacky
Posts: 2981
Location: Louisiana | TheOldGrayMare - 2016-10-31 3:33 PM
This is where I got my brand from and am very pleased with it:
http://flying45.com/
Mine also came from Flying45. We haven't actually gotten around to using it lol. Waiting until we have the whole barn's teeth done. That way the ones that will need sedating will already be knocked out.
I have a couple crazies I'm not chancing a botch job on haha. |
|
| |
|
Location: In my own little world | Interesting comments on freeze branding. We have built irons and freeze branded since about 2001. Probably branded over 3000 head of horses and several hounds.. Our irons are built using 1/4" cold roll round stock steel. We experimented with brass, copper, stainless and settle in the cold roll steel for horse irons. There are many advantages to using a brand that you can see through rather than a solid piece of brass. We especially don't care to use brass irons when it's a jaw brand. We brand with liq nitrogen and our average length of time to stay in a horse is 12-13 seconds. If it is a light grey or white horse we will stay in for about 30 seconds to kill color and growth follicle. There are some crucial steps and ways of doing it that make a huge difference. We get a lot of referrals from vets. |
|
| |
|
Expert
Posts: 4766
Location: Bandera, TX | streakysox - 2016-10-31 1:00 PM Mine is brass and got it from L and H branding irons
The best there is!
Horses or cattle. |
|
| |
|
Midget Lover
Location: Kentucky | Two Nickles - 2016-10-31 3:48 PM What size are your freeze brands? I assumed their was just a standard but am seeing several size options with L & H.
My colt brand is 3". |
|
| |
|
Expert
Posts: 2097
Location: Deep South | FLITASTIC - 2016-10-31 3:02 PM
BamaCanChaser - 2016-10-31 11:18 AM
Mine is also brass, and like already mentioned, you're timing has to be impeccable for a perfect white brand.
We shave the hair as close as possible. Wipe with rubbing alcohol to get it clean. Then press the brand hard against them, gently rocking it up and down for 10 seconds. This is for older horses. I've heard if branding horses younger than a year older their skin is thinner and you can only leave it on for about 7 seconds.
I freeze brand as a side job of sorts... I use liquid nitrogen ( Best predictable method ) and Minimum 17 seconds to 24 seconds depending on color of the horse. I can't imagine 7-10 seconds getting the job done. : )
We use liquid nitrogen as well. All of the ones we have left on for 15-20 seconds have finished "bald" no white hair growth.
Wonder if geography has anything to do with it? Weird! |
|
| |
|
Location: Not Where I Want to Be | uno-dos-tres! - 2016-11-01 4:31 AM streakysox - 2016-10-31 1:00 PM Mine is brass and got it from L and H branding irons The best there is!
Horses or cattle.
Why?
|
|
| |
|
Location: In my own little world | 1DSoon - 2016-11-01 7:57 AM
uno-dos-tres! - 2016-11-01 4:31 AM streakysox - 2016-10-31 1:00 PM Mine is brass and got it from L and H branding irons The best there is!
Horses or cattle.
Yes why? Irons are subjective IMO. |
|
| |
Folks on-line